This is the dropship I've been waiting for...
Tornadodo Dropship
I can see this being very useful for the RPG as well!
...and I may need to replace the static fan blades with acrylic to give a sense of motion...
CNC Workshop Tornadodo Dropship
10 posts
• Page 1 of 1
Yeah, I agree that is a really nice aircraft. That might actually be the first piece of mdf scenery I buy.
Dave H
splayedpaintbrush.com
splayedpaintbrush.com
- splayedpaintbrush
- Posts: 65
- Joined: February 11th, 2015, 2:43 am
- Location: Leyland, UK
- Has liked: 21 times
- Been liked: 23 times
schoon wrote:This is the dropship I've been waiting for...
Tornadodo Dropship
I can see this being very useful for the RPG as well!
Man, gotta add that to my CNC workshop list of things I want...
...and I may need to replace the static fan blades with acrylic to give a sense of motion...
Another trick is paint and seal the fan blades, then cover with epoxy and swirl the epoxy. Might be a challenge with the open fans, though!
“I'm curious, son. When has 'This might be a trap' ever stopped you?”
“Stopped? Never. Slowed me down while I load the guns? Every time.”
-Schlock Mercenary, 22 July 2013.
“Stopped? Never. Slowed me down while I load the guns? Every time.”
-Schlock Mercenary, 22 July 2013.
Section9 wrote:schoon wrote: ...and I may need to replace the static fan blades with acrylic to give a sense of motion...
Another trick is paint and seal the fan blades, then cover with epoxy and swirl the epoxy. Might be a challenge with the open fans, though!
You've piqued my curiosity - do you have a pic that demonstrates this technique?
No, read about it in a Fine Scale modeler, guy was building a diorama with an A6 in flight and mentioned doing that to the engine intakes (mounted the bird with acrylic rods into the exhausts).
I'm not sure about the materials of the fan blades, from the assembly instructions it looks like they might be 1mm acrylic already.
I'm not sure about the materials of the fan blades, from the assembly instructions it looks like they might be 1mm acrylic already.
“I'm curious, son. When has 'This might be a trap' ever stopped you?”
“Stopped? Never. Slowed me down while I load the guns? Every time.”
-Schlock Mercenary, 22 July 2013.
“Stopped? Never. Slowed me down while I load the guns? Every time.”
-Schlock Mercenary, 22 July 2013.
Section9 wrote:I'm not sure about the materials of the fan blades, from the assembly instructions it looks like they might be 1mm acrylic already.
Or card. CNC is branching into MDF+card latelly.
If not worth saving, is it worth rewriting? What is more, was it worth writing?
- Mob of Blondes
- Posts: 1591
- Joined: January 31st, 2013, 11:13 pm
- Has liked: 1 time
- Been liked: 198 times
I believe the blades are normally thinner MDF, though I don't know for sure.
I wrote them am email, and they're willing to replace the fans with solid clear acrylic pieces, so long as I order over $100 of stuff.
I'll report again after I see it all in the MDF!
I wrote them am email, and they're willing to replace the fans with solid clear acrylic pieces, so long as I order over $100 of stuff.
I'll report again after I see it all in the MDF!
This arrived in the post today - I haven't had a chance to unbox yet, but it looks good from the outside!
More when I get everything out of the shrink wrap...
More when I get everything out of the shrink wrap...
Looking forward to the unboxing 
-
el_presidente - Posts: 186
- Joined: September 9th, 2014, 10:50 am
- Has liked: 12 times
- Been liked: 43 times
Section9 wrote:I'm not sure about the materials of the fan blades, from the assembly instructions it looks like they might be 1mm acrylic already.
Its card definately card.
What I do: Chef by trade, arsehole by choice and I play and TO for Infinity when I'm not being either.
10 posts
• Page 1 of 1